logo
icon
logo

2k Green

RITVER 2K ACRYLIC GREEN is a high build topcoat based on acrylic polyol and aliphatic isocyanate. The product is strongly recommended as a pigmented topcoat for all kinds of vehicle refinish. It exhibits excellent opacity, weather resistance, gloss retention, color fastness, as well as balanced hardness and flexibility.

SKU: ARP335-Green

  • spe_5

    FINISH

    FINISH
  • spe_5

    COLOR

    Green
  • spe_5

    SPECIFIC GRAVITY

    0.98 g/mL ± 0.05
  • spe_5

    SOLIDS (% by vol.)

    51 ± 2
  • spe_5

    FLASH POINT

    <21⁰C
  • SUITABLE SUBSTRATES
  • SURFACE PREPARATION
  • TECHNICAL DATA
  • TECHNICAL TIPS
  • APPLICATION PROCESS
  • STORAGE AND SHELF - LIFE
  • HANDLING
  • SAFETY PRECAUTIONS

RITVER TOPCOAT 2K is most suitable to be applied over 2K Ritver Primer (PS 1756).

Ensure that the surface is properly prepared, sanded and smoothened. Blow off sanding dusts using compressed dry air and then clean using a solvent degreaser to remove oils, grease and grimes before any application paint application is conducted. Use a new cloth so as to ensure that re-contamination is avoided. Apply the primer, PS1756, then sand it then over coat it with RAP Topcoat.

VISCOSITY (25⁰C) 180 seconds ± 20 (Ford cup no.4
HARDENER ARP004 (2K Standard Slow Hardener),
ARP006 (2K Standard Fast Hardener)
DILUENT PT6001 (2K Slow Thinner)
POT LIFE (@25⁰C) Maximum 4 hours after mixing with hardener
SPREAD RATE 112.5 m2 / L

1. It is strongly recommended to use personal protective equipment during application.
2. Product should be stirred properly prior to use.
3. Prior to application, use of filter is recommended to avoid dust particles.
4. Clean the gun properly before and after usage.

PRODUCT RITVER 2K TOPCOAT GREEN
HARDENER ARP004 (2K Standard Slow Hardener)
ARP006 (2K Standard Fast Hardener)
THINNER PT6001 (2K Thinner)
MIXING RATIO Mix by weight
RITVER 2K TOPCOAT: 100
RITVER 2K HARDENER: 50
RITVER 2K THINNER: 25-30
SPRAY VISCOSITY 18 – 20 Sec (DIN4 at 25⁰C)
SPRAY EQUIPMENT For spray application, we recommend
using HVLP Spray Gun
Nozzle size: 1.3 – 1.4 mm
Pressure: 2 bar (29 psi inlet)
NUMBER OF COATS Apply 2 – 3 coats
FLASH TIME Flash off time: 5 – 10 minutes coats.
Allow drying for 15 minutes prior to
baking.
DRYING FILM
THICKNESS		 30 – 40 microns
DRYING TIME Air Dry at 25⁰C
Dust Free: 15 minutes
Touch Dry: 60 minutes
Hard Dry: 24 hours
Baking at metal temperature of 60⁰C
Hard Dry: 25 minutes

Under dry and cool condition, Storage stability can be sound up to 2 years in original sealed containers.

Disposal: As per the guidance and legislations of the local Authority e.g., by controlled landfill.
In case of doubt, consult local authority. Do not empty into drains, sewers or other water courses.
Caution: It is strongly advised not to keep open half used drums as it forms a skin on the top layer.

Avoid contact with the skin and eyes. Wear suitable protective clothing such as overalls, goggles, dust mask and gloves. Use a barrier cream.
Ensure that there is adequate ventilation in the area where the product is being applied. Do not breathe vapour or spray.
MSDS is available on request for the safe handling of this product.
FIRST AID
Eyes: In the event of accidental splashes, flush eyes with warm water immediately and obtain medical advice.
Skin: Wash skin thoroughly with soap and water or approved Industrial cleaner. DO NOT USE solvent or thinners.
Inhalation: Remove to fresh air, loosen collar and keep patient rested.
Ingestion: In case of accidental ingestion DO NOT INDUCE VOMITING. Obtain immediate medical
attention.
NOTE:
This product can be used even as non-yellowing fixative on lacquer manufactured, treated with ageing products; be sure of the compatibility with the products used in the varnishing cycle

Related products