logo
icon
logo

Acrylic Topcoat Clear Multicoat (5%-10%-30%-50%-Gloss)

Two component Acrylic Topcoat Clear Multicoat Fire Rated suitable as basecoat and topcoat. It is particularly suitable for applications where non- yellowing and fire retardant properties are required. [This product is certified by Thomas Bell-Wright following the Multi-coat Interior Finish Systems for Reaction to Fire performance according to test standard ASTM E84-19a and approved by Dubai Civil Defense under license no.
LMTNA0000135842-2019].

SKU: AT42XX-MC

  • spe_5

    Appearance

    5%, 10%, 30%, 50%, Gloss
  • spe_5

    Color

    Transparent
  • spe_5

    Specific gravity

    1.00 Kg/L [±0.025]
  • spe_5

    Weight Solids

    Approx. 27% [± 2]
  • spe_5

    Flash Point

    21oC
  • USES
  • SURFACE PREPARATION
  • CATALYST
  • APPLICATION METHODS
  • CLEANING
  • PACKING & STORAGE
  • SAFETY & FLAMMABLE

Applicable on pale wood as [maple, birch, ash, reconstructed veneers, etc…], and further coating as white or pastel colored the surfaces and protect them from yellowing

All timber species must be fully aged with a moisture content of less than 15%. The surface must be dry, clean and free from contaminations. Natural oil or gum must be removed by solvent
cleaning.
To obtain optimum surface finish sand the wood properly in the same direction of the wood grain, utilize sanding paper no. [100]. After sealer dry , utilize paper No.[220] to create smoothness to the substrate , then utilize paper No.[400 ] to achieve perfection of substrate . Apply basecoat [AB401] Acrylic sanding Sealer till reaching between coats is essential, as is adequate sanding and removal of dust prior to application of first coat [AT42XXMC] Acrylic Topcoat Clear Multicoat. Control the compatibility of Stains eventually used.

By weight By volume
20% CA040 20%

Pot Life 8 hrs. @ 25°C
Stir product well with a flat paddle. Add the correct quantity of hardener and stir till homogeneous. Thin to required viscosity. For details of spray equipment contact Ritver Technical Services Department.

Dilution
Utilize [TP292] PU Thinner depending on the application system used. In general 20 -30% thinner
is added to achieve an application viscosity. This is suitable for spraying.
For Curtain coater 10-20% Thinner is added to achieve an application viscosity. In case of high humidity climate add 5% [TP222] PU retardant thinner.

Depends on the finishes required but in general an appropriate rate is 120 gr / sq. m. The number of coats depends on the surface preparation the porosity of the substrate, and the finish required.
Following Treatments
By spray gun: Utilize nozzle 1.8 – 2 mm at 3-4 ATM/bar. For details of spray equipment contact Ritver Technical Services Department.
By Curtain Coater: It is recommended to control the viscosity during application by adding PU Thinner to balance the evaporation of solvents.

Cleaning
Clean all tools and equipment immediately after use with [TC010] Tool Cleaner.

Available in 5Ltr, 25Ltr.
Store in a cool and well ventilated place. Keep away from direct sunlight. Maximum 18 months in unopened container, stored in a cool and dry condition at 25°C.

This material is flammable and must not be exposed to naked flames.
Use only in well ventilated areas. In case of insufficient ventilation during application, wear suitable respiratory equipment. Do not breathe vapor / spray. In case of contact with eyes, rinse immediately with plenty of sweet water and seek medical advice. In case of contact with skin, wash immediately with soap and water or a recognized skin cleaner.
Keep away from sources of ignition. No Smoking. Keep out of reach of children.

Related products