logo
icon
logo

Epoxy Topcoat Solvent Base

CONCOAT EP160 is a high performance, two component, solvent based epoxy resin floor coating top coat. The cured film forms a hard coating with excellent adhesion to concrete, and granolithic screeds, and certain metal surfaces. It cures to a semi-glossy,
impervious finish which can be easily cleaned.
CONCOAT EP160 is available in wide range of colors and in clear grade.
CONCOAT EP160 complies with BS 476, Part 7: 1971 and BS 5493 – 1971.

SKU: Concoat EP160

  • USE
  • ADVANTAGES
  • SURFACE PREPARATION
  • MIXING
  • APPLICATION
  • COVERAGE
  • CLEANING
  • PACKAGE
  • STORAGE
  • TECHNICAL PROPERTIES
  • FLAMMABILITY
  • SHELF LIFE
  • HEALTHY AND SAFETY

CONCOAT EP160 is medium duty traffic floor coating suitable for use in production assembly areas, workshops, dairies, soft drinks production and bottling plants, kitchens, showrooms, wet working areas and car parking areas.
CONCOAT EP160 provides a hard wearing, easily cleaned and attractive floor coatings in areas where high resistance to chemical attack is required.
CONCOAT EP160 is used as a final coating on sealed (primed) concrete floors and as a finish coat for epoxy floor screeds to provide a more durable and easily cleaned surface where high impact is desirable.
ADV

  • High impact resistance.
  • Hard wearing – durable.
  • Low maintenance costs.
  • High abrasion resistance.
  • Provides hygienic – impervious finish
  • Excellent adhesion to various substrates.
  • Applicable to apply on floor and walls.
  • High abrasion resistance.
  • Provides hygienic – impervious finish.

All surfaces should be clean, dry and free from dust and other contaminants. Wet substrates should be used sponge dried to remove all surface water, then dried. Treat oil or grease contamination should be removed by degreaser followed by water or steam cleaning.
New concrete floors should be at least 28 days and have a moisture content of less than 5%. Excessive laitance should be removed by mechanical method. Dust and other debris should be removed by vacuum cleaning.
Old concrete floors damaged areas or surface irregularities should be repaired by using EPOMORTAR FC two component fast curing epoxy mortar (Refer to TDS).
Epoxy Screeds high spots or trowel marks should be rubbed down and remove dust
and debris by vacuum cleaning then repair it by using EPOSCREED 10 three
component epoxy screed (Refer to TDS.)

The entire contents of the hardener container should be poured into the base container and the two materials mixed thoroughly for at least 3 minutes. Use of heavy duty slow speed power drill with a jiffy mixing blade. Mix the two components in the quantities supplied taking care to ensure hardener container is scraped clean. Do not add solvent thinners at any time.

CONOCOAT EP160 is recommended to apply in two coats. CONCOAT EP160 can be applied to prepared surface using airless spray, brush or roller.
Ensure that the area is completely coated.
The second coat can be applied after the first coat has initially dried (typically 12 to 18 hours at 35 0C).

5.5 m2 /lit. at 100 microns (DFT) in two coats.

Tools and equipment can be cleaned immediately by using THINNERCOAT 10 organic solvent.

16 liter pack (including colored base and hardener)

Product should be stored at 25°C in dry conditions and keeping away from source of flame.

Mixed Density 1.43 + 0.05 depending on color
Volume Solids
ASTM D 2823 – 91		 57 % + 2
Application Temperature 12 0C to 35 0C
Tack Free Time 1-2 hours at 35 0C.
Initial Hardness 20 hours at 350C.
Pot Life 5 hours at 35 0C.
Full Cure 5 days at 35 0C.
Shore A Hardness
ASTM D 2240 – 91		 80
Pull – Off (On concrete)
ASTM D 4541 – 85		 2.5 N/mm2 (CF)
Abrasion Resistance
(ASTM D 1044-85, CS-17
Wheel 500 gm load)		 100 cycles 5 -10 mg
500 cycles 35 – 45 mg
1000 cycles < 90 mg
Flash Point 32 0C.
Chemical Resistance: Gasoline Excellent
Petrol Excellent
Diesel Excellent
Engine Oil Excellent
NaOH20% Good
H2SO410% Good
HCl10% Good
Acetic 5% Good
Brake fluid Excellent

CONCOAT EP160 and THINERCOAT 10 are flammable materials so do not expose to naked flames during application.

12 months in tightly closed container.

The application of material should be in good ventilation and avoid inhalation of the vapors. Use goggles and vinyl gloves. In case of contact with eyes, rinse immediately with plenty of clean water, do not use solvent and seek medical attention immediately.
The product complies with environmental and occupational health & safety standards ISO 14001 and OHSAS 18001.

Related products